PWM Fan
PWM Fan is a Unraid plugin that controls the speed of PWM (pulse-width modulation) fans for the CPU and hard drives, offering single-fan mode for the CPU and…
Platform availability
Available on 1 of 10 platforms
- Unraid
- TrueNAS (not listed)
- Umbrel (not listed)
- ZimaOS (not listed)
- Proxmox (not listed)
- Helm (not listed)
- Mac (not listed)
- Windows (not listed)
- Linux (not listed)
- Any server (not listed)
Health score?A 0-100 score computed nightly from four factors: maintained (40%: recent commits and steady activity), popular (25%: GitHub stars, log scale), easy to install (20%: platforms, install notes, setup guides, Docker image) and light to run (15%: minimum RAM, ARM support). When the source code has been checked, a fifth factor, security check (20%: automated scan for committed secrets, unsafe desktop-app settings, known-vulnerable dependencies and project hygiene; any serious finding caps it at 20), is added. Factors without data are left out and the rest are rescaled.
28/100 Low
- Maintained
- 0last commit 1027 days ago
- Popular
- 2927 GitHub stars
- Easy to install
- 251 install platform, install notes
- Light to run
- No data
- Security check
- 85no serious findings, CI
Based on 4 of 5 factors.
Availability: platform listings confirmed today, links checked 5 days ago
- GitHub stars
- 27
- Open issues
- 0
- Last commit
- 2024-01-28
- Latest release
- v1.0.0
- License
- Apache-2.0
- Activity
- stale
Checked today - source: GitHub (sparky8512/usb-pwm-fan)
Resources & Compatibility
Requirements not published yet.
First-install notes
- Check your PCA9685 board is wired Before starting, make sure the PCA9685 fan/servo driver board is connected to the correct I2C (wiring bus) pins; if the check fails, the app stops and nothing will move. source
- Set the right PWM frequency Set the PWM frequency to 50 Hz for standard servos or fans, instead of leaving the default 1000 Hz; the wrong speed makes them buzz, jitter, or not follow commands. source
- Use the default I2C address unless changed Use the driver's default I2C address (0x40) unless you have changed the board's address; the wrong address means your board won't be found even if the wires are correct. source
- Hardware The plugin ships firmware and software for a USB fan controller: it drives the fan's PWM (pulse-width modulation) input, reads its tachometer output, and is suitable for standard PC case or CPU fans. source
Fetched today - each note links to its source
Variants
Alternatives
No alternatives collected yet.
Common questions
Does PWM Fan require 4-pin fans for speed control?
PWM speed control uses the 4-pin PWM line, while 3-pin fans only have ground, 12V, and tachometer and are controlled by voltage. A 4-pin fan is the normal requirement for PWM fan control.
Can a fan splitter or hub cause PWM Fan fans to run at full speed?
Fans can stay at maximum speed even after BIOS PWM or silent settings, and fan splitters and multiple fans are reported as possible causes. Check the splitter or hub wiring if a fan will not slow down.
Why might a cheap fan buzz under PWM Fan control?
A default 4 kHz PWM signal can make cheap fans buzzy. Raising the PWM frequency can help reduce the buzz.
Do PWM Fan settings survive a device reboot?
The USB PWM firmware can save current fan and LED configurations so they are restored when the device is rebooted.
Answers sourced from community.home-assistant.io, github.com, www.reddit.com, www.reddit.com
Community
- Why are my fans running so loud even after I adjusted settings ... - Reddit (reddit)
- [SOLVED] - How to control PWM fans in Bios or Software? (forum)
- Simple PWM Fan Control with Tasmota - Home Assistant Community (other)
- Controlling a CPU/case fan with GPIO PWM based on CPU temperature (other)
- [SOLVED] - Recommended software for controlling PWM case fans connected ... (forum)
Collected 48 days ago - public community threads